| Important News |
 |
| |
| News Flash - Reilang Oil Cans |
29/03/2006 |
Reeves 2000 is please to be able to offer Reilang Oil cans. We currently
stock 300ml cans with the choice of a fixed or flexible spout. We also stock
200ml cans with a fixed spout. Buy
Now |
| |
|
| News Flash - Kate's Crazy Marathon Idea |
27/03/2006 |
Less than 4 weeks to go until the marathon!
I have just completed my longest run to date - 16 miles, so not feeling too good at the moment. Still no rest for the wicked, back at work in the afternoon moaning that everything is aching and as for the blisters, don't get me started!
Thanks to Tash for reminding me I have a further 10 miles to go.
I have recovered from my assult by the Alsatian. The bruise has gone on my backside which amused everyone at work. Funny now but a little concerning when it was just me and the dog!
Thanks to everyone who has sponsored me so far. This marathon business is about as difficult as I expected, and then more!
If you would like to sponsor me, I am running for MS Society http://www.justgiving.com/kbarton.
|
| |
| News Flash - Kate's Crazy Marathon Idea |
07/02/2006 |
After a couple of drinks during a England's dominating victory over Australia
at Edgbaston, I mentioned that I would like to run the London Marathon.
To my surprise Craig agreed and we foolishly sent off the forms.
Months passed and nothing was heard, we presumed the best, we hadn't
got in, then there was the phone call - 'we have two spaces available,
are you two still up for it!'. A quick chat with Craig and it was agreed,
we will be running the London Marathon!
Now comes the training and the fund raising. I have chose to run for
the MS Society .............. if you would like to help me with the latter
please visit http://www.justgiving.com/kbarton.
Just so we are all clear, training starts tomorrow!
|
| |
| News Flash |
01/11/2005 |
| Our extension is now complete and fully operating......which
means more space for more stuff! |
| |
| News Flash |
06/01/2005 |
| 40oz injectors are available as part of the International
Range |
| |
| News Flash |
02/10/2004 |
| 18oz injectors are now back in stock. We also have 25oz injectors
as part of the International Range available. Please note both injectors
have been tested 'vertically' and run successfully |
|
| News Flash |
07/10/2004 |
| After many months of struggling we have finally been able to
cast the cylinder blocks for King George. All three cylinders are now only
available in Gun Metal. |
| |
|
| |
| News Flash |
12/05/2004 |
| Images from the recent Harrogate Exhibiton are now available.
Review |
|
| News Flash |
11/04/2004 |
| A review of the recent exhibiton held at Taunton is now available.
Review |
|
| News Flash |
13/03/2004 |
| Order are now being taken for the exhibition at Harrogate. |
|
| News Flash |
12/01/2004 |
| Order are now being taken for the exhibition at Wembley. |
|
| News Flash |
12/01/2004 |
| We have once again expanded our International
Range. The new items include Axle Feedpumps and Boiler Feedpumps |
|
| News Flash |
09/10/2003 |
| The new price list is now available. Please send 4 x 1st class
stamps to receive your copy now |
|
| News Flash |
26/09/2003 |
| The Prairie Cylinder Blocks (18/163) are currently at
the foundry being cast. The castings should be available shortly |
|
| News Flash |
26/09/2003 |
| New products are available in our International Range, including
Blower Valves and Displacement Lubricators - details to follow
shortly |
|
| News Flash |
26/09/2003 |
| 18oz Injectors, from the International
Range (39/504), are now back in stock. |
|
| News Flash |
26/09/2003 |
| Foden 3" Rear Wheels (33/228) are now available.
Front Wheels (33/227) will be available in the next couple of weeks |
|
| News Flash |
19/09/2003 |
| The majority of the 'WORKSHOP EQUIPMENT' castings
formerly supplied are now once again available. Further details will be
published shortly. Alternatively please contact us for more informaiton.
|
|
| News Flash |
19/06/2003 |
|
Tich Axlebox Springs are now going to have to be made to order, which
means the cost of these springs will increase from approximately £3.00
to over £50.00! As a result we recommend using the following;
1/058 - Workshop Practice Series #19 - Spring Design and
Manufacture £6.95
44/608 - Stainless Steel Spring Wire 24 swg (7.5m) £1.88 inc vat
|
|
| News Flash |
31/07/2003 |
| The new rear wheel pattern for the 3" Foden has now been
completed and is now lodged with the foundry! |
|
| New Products |
22/07/2003 |
| View products recently added the Reeves product range |
| See More >> |
|
| News Flash |
19/06/2003 |
| Congratulations to Tasha (the one who answers the phone) who
has just completed the world's highest bungy jump in South Africa, raising
over £1000 for Cancer Research - photos will be available in a couple
of weeks |
|
| |
| New Flash |
19/06/2003 |
|
Congratulations to Tasha (the one who answers the phone) who has just
completed the world's highest bungy jump in South Africa, raising over
£1000 for Cancer Research
|
|
| Injectors |
29/05/2003 |
| 40oz and 60oz 'JC' injectors are now back in stock |
|
| |
| Pattern Problems |
29/05/2003 |
| For the very patient customers awaiting Foden 3" rear wheels
and Prairie cylinder blocks, the new core prints are due back next
week, so patterns will be sent to the foundries immediately |
|
| |
| Price Increases |
29/05/2003 |
| Having examined the 'old' Reeves pricing structure on
castings it would appear that it was largely based on complexity of pattern
- especially in the Don Young Range. Today foundries are charging
on a weight basis except in a few cases of multi cored patterns such as
Paddington & King cylinder blocks. Thus we have decided to weigh
and re-cost every casting (we have done over 6000 so far!) This has resulted
in some items, such as larger wheels, more than doubling. In most cases
we have capped this increase at 100% as we feel we cannot pass on such a
great increase. To note, some other items, particularly in the Don Young
range have come down. We accept this is no consolation to those not on these
models. |
|
| |
| Axleboxes in the Don Young range |
29/05/2003 |
| Many of these are subject to a very high price increase, yet
much of the product is to be wasted once machined. We are going to re-examine
these patterns to help reduce these costs |
|
| |